Vim Tips Wiki
Tip 312 Printable Monobook Previous Next

created August 13, 2002 · complexity intermediate · version 6.0

Here is how to cut-and-paste or copy-and-paste text using a visual selection in Vim. See Cut/copy and paste using visual selection for the main article.

Cut and paste:

  1. Position the cursor where you want to begin cutting.
  2. Press v to select characters, or uppercase V to select whole lines, or Ctrl-v to select rectangular blocks (use Ctrl-q if Ctrl-v is mapped to paste).
  3. Move the cursor to the end of what you want to cut.
  4. Press d to cut (or y to copy).
  5. Move to where you would like to paste.
  6. Press P to paste before the cursor, or p to paste after.

Copy and paste is performed with the same steps except for step 4 where you would press y instead of d:

  • d stands for delete in Vim, which in other editors is usually called cut
  • y stands for yank in Vim, which in other editors is usually called copy

Copying and cutting in normal mode[]

In normal mode, one can copy (yank) with y{motion}, where {motion} is a Vim motion. For example, yw copies to the beginning of the next word. Other helpful yanking commands include:

  • yy or Y – yank the current line, including the newline character at the end of the line
  • y$ – yank to the end of the current line (but don't yank the newline character); note that many people like to remap Y to y$ in line with C and D
  • yiw – yank the current word (excluding surrounding whitespace)
  • yaw – yank the current word (including leading or trailing whitespace)
  • ytx – yank from the current cursor position up to and before the character (til x)
  • yfx – yank from the current cursor position up to and including the character (find x)

Cutting can be done using d{motion}, including:

  • dd - cut the current line, including the newline character at the end of the line

To copy into a register, one can use "{register} immediately before one of the above commands to copy into the register {register}. See pasting registers for more information on register syntax.

Pasting in normal mode[]

In normal mode, one can use p to paste after the cursor, or P to paste before the cursor.

The variants gp and gP move the cursor after the pasted text, instead of leaving the cursor stationary.

To select a register from which to paste, one can use "{register}p to paste from the register {register}. See pasting registers.

Pasting in insert mode[]

The contents of a register can be pasted while in insert mode: type Ctrl-r then a character that identifies the register. For example, Ctrl-r then " pastes from the default register, and Ctrl-r then 0 pastes from register zero which holds the text that was most recently yanked (copied). See pasting registers.

Copying and cutting in command-line mode[]

Command-line mode occurs after typing : to enter a command. By default, while in the command line, typing Ctrl-f opens the command-line window where commands can be edited using normal mode. For example, part of one command can be copied then pasted into another command. See using command-line history.

Pasting in command-line mode[]

There are two approaches to pasting in command-line mode. The first is to open the command-line window with Ctrl-f, then use normal-mode commands to paste. See the previous section.

The second approach is to type Ctrl-r then a character to paste the contents of the register identified by the character. See Pasting in insert mode above.

Copy, cut, and paste from the system clipboard[]

Main article: Accessing the system clipboard

Unlike most text editors, Vim distinguishes between its own registers and the system clipboard. By default, Vim copies to, cuts to, and pastes from its own default register, called the unnamed register ("", also called quotequote) instead of the system clipboard.

Assuming Vim was compiled with clipboard access, it is possible to access the "+ or "* registers, which can modify the system clipboard. In this case, one can copy with e.g. "+y in visual mode, or "+y{motion} in normal mode, and paste with e.g. "+p.

If your installation of Vim was not compiled with clipboard support, you must either install a package that has clipboard support, or use an external command such as xclip as an intermediary. See Accessing the system clipboard for detailed information.

Multiple copying[]

Main article: Pasting registers.

Deleted or copied text is placed in the unnamed register. If wanted, a register can be specified so the text is also copied to the named register. A register is a location in Vim's memory identified with a single letter. A double quote character is used to specify that the next letter typed is the name of a register.

For example, you could select the text hello then type "ay to copy "hello" to the a register. Then you could select the text world and type "by to copy "world" to the b register. After moving the cursor to another location, the text could be pasted: type "ap to paste "hello" or "bp to paste "world". These commands paste the text after the cursor. Alternatively, type "aP or "bP to paste before the cursor.

Windows clipboard[]

When using Vim under Windows, the clipboard can be accessed with the following:

  • In step 4, press Shift+Delete to cut or Ctrl+Insert to copy.
  • In step 6, press Shift+Insert to paste.

Different instances[]

How does one copy and paste between two instances of Vim on different Linux consoles?

After copying text, open a new buffer for a new file:

:e ~/dummy
  • Paste the text to the new buffer.
  • Write the new buffer :w.
  • Switch to the previous buffer :bp to release *.swp.
  • Now switch to the other console.
  • Put the cursor at the desired place.
  • Read the dummy file :r ~/dummy

Increasing the buffer size[]

By default, only the first 50 lines in a register are saved, and a register is not saved if it contains more than 10 kilobytes. :help 'viminfo'

In the example below, the first line displays the current settings, while the second line sets:

  • '100 Marks will be remembered for the last 100 edited files.
  • <100 Limits the number of lines saved for each register to 100 lines; if a register contains more than 100 lines, only the first 100 lines are saved.
  • s20 Limits the maximum size of each item to 20 kilobytes; if a register contains more than 20 kilobytes, the register is not saved.
  • h Disables search highlighting when Vim starts.
:set viminfo?
:set viminfo='100,<100,s20,h

See also[]